type 1 crush material weight per m3

Contractors Price List 2018 - Orkney Aggregates

CLASS 6N - Table 6/1 weight approx. 1.7 Tonnes/m³ £8.45 per tonne 75mm down. Suitable as hardcore on roads/sites where excavations are shallow, (up to approximately 120mm). TYPE 1 - Table 8/2 weight approx. 1.85 Tonnes/m³ £8.45 per tonne 50mm down. Well graded granular material recommended for preparing roads/sites prior to

Construction Aggregate Calculator - Vulcan Materials Company

Use this calculator to estimate the quantity of Construction Aggregates needed for your particular job, based on width, length, thickness, and product density.

Sub-Base Aggregates Supplier | Day Group

Type 2: Recycled. An unbound sub-base material with more fines and a wider grading envelope than Type 1. Normally used as a layer under Type 1. 6F5 Recycled (Formerly 6F2 Recycled) Typically used for capping sub formations prior to laying Type 1 or Type 2 sub-base. Well graded material ranging from 125mm to dust. 6F4 Recycled (Formerly 6F1 ...

SECTION 4-01 MINERAL AGGREGATES Page 4 - 1

Type 1 and Type 2 except as follows. Crushed gravel may be used in lieu of Crushed Rock, Mineral Aggregates Type 1 and Type 2 as a surface ballast course under the following conditions: 1. only when specified inthe Contract for specific locations or uses; and . 2. meets the requirements of Section 4-01.

Calculate Recycled Concrete Road base | cubic yards / Tons

Type in inches and feet of your project and calculate the estimated amount of Recycled Materials in cubic yards, cubic feet and Tons, that your need for your project. The Density of Recycled Concrete Road base: 2,410 lb/yd³ or 1.21 t/yd³ or 0.8 yd³/t

Calculate Quantities of Materials for Concrete -Cement ...

The quantities of materials for 1 m3 of concrete production can be calculated as follows: The weight of cement required = 7.29 x 50 = 364.5 kg. Weight of fine aggregate (sand) = 1.5 x 364.5 = 546.75 kg. Weight of coarse aggregate = 3 x 364.5 = 1093.5 kg. Concrete Calculator: Calculate Quantities of Materials for Concrete

Mot type 1 weight per cubic meter - answers.com

Need thickness and possibly the type of paint or it's weight per cubic metre or something like that. ... 1 kg of any material weighs the same as 1 kg of any other material. With normal Earth ...

APPENDIX A WEIGHTS OF BUILDING MATERIALS

APPENDIX A WEIGHTS OF BUILDING MATERIALS SECTION A101 GENERAL In estimating dead loads for purposes of design, the actual weights of materials and constructions shall be used, provid­ ... DEAD LOAD IN POUNDS PER CUBIC FOOT For SI: 1 in = 25.4 mm, 1 psf = 47.8803 Pa.

Tonnes of Granular B to m3 - OnlineConversion Forums

Re: Tonnes of Granular B to m3 Usually, the granular a or b material will be requested to be compacted to 95%, 98% or SPMDD. The unit weight will be slightly different depending the different SPMDD. it is also affected by other factors such as the specific gravity of the stome material, shapes of the stones and the gradations, etc.

Mass, Weight, Density or Specific Gravity of Bulk Materials

The specific gravity of all other materials are compared to water as a fraction heavier or lighter density. For example, ammonium nitrate has a specific gravity (sg) of 0.73 while dry ammonium sulphate has a sg of 1.13 (1130 kilograms/cubic metre) (see table below)

Convert volume to weight: Stone, crushed - AquaCalc

Stone, crushed weighs 1.602 gram per cubic centimeter or 1 602 kilogram per cubic meter, i.e. its density is equal to 1 602 kg/m³. In Imperial or US customary measurement system, the Stone, crushed density is equal to 100 pound per cubic foot [lb/ft³], or 0.926 ounce per cubic inch [oz/inch³] .

Crusher Run Weight Per M3 - malizia.be

weight of 2.5 crusher run per m3 grinding mill chinathis page is about what does 1 cubic meter of crusher run weight, convert tonne m3 crusher run depends on the weight per cubic foot of the dirt and that weight of 2.5 crusher run per m3 crusher, quarry, weight of 2.5 crusher run per m. 17 251 usd. paper dictionary absolute .

Material Weights - Harmony Sand and Gravel

Most of Harmony Sand & Gravel's products will weight approximately 2,840 pounds per cubic yard or about 1.42 tons per cubic yard. For estimating purposes, most Contractor's consider the yield to be 3,000 pounds per cubic yard or 1.5 tons per cubic yard.

Density of Common Building Materials per Cubic Foot - RF Cafe

Density of Some Common Building Materials: These values for density of some common building materials were collected from sites across the Internet and are generally in agreement with multiple sites. Most are from BOCA or ASAE tables. However, if you have values that you believe are more accurate, use them for your calculations, and please send ...

weight of granite per cubic meter - BINQ Mining

Standard Weights for Crushed Rock Per Meter | . Standard Weights for Crushed Rock Per Meter.The weight of crushed rock will vary greatly depending on the type … How to Crush Stone; The Weight of One Cubic Meter … »More detailed

How much does a cubic yard of road base weigh - answers.com

Concrete . Normal weight concrete -- a mixture or sand, cement, and stone gravel -- has an accepted density of 145 pounds per cubic foot. Since there are 27 cubic feet per cubic yard, a cu.yd ...

Type 1 Crushed Concrete - Smiths Bletchington

Type 1 Crushed Concrete. Type 1 Concrete is produced by crushed aggregate - recycling waste materials from construction and demolition projects. It is perfect for using in trench fills, backfills, oversite fills and as a granular sub-base. WRAP Protocal. Applications:

weight of steel in reinforced concrete per cubic meter

weight of steel in reinforced concrete per cubic meter. A normal weight concrete weighs 2400 kg per cubic meter or 145 lbs per cubic foot (3915 lbs per cubic yard). The unit weight of concrete (density) varies depending on the amount and density of the aggregate, the amount of entrained air (and entrapped air), and the water and cement content.

MOT Type 1 - Loose, bagged & in stock! - Axtell

We do stock another variation, MOT Type 1 - Crushed Concrete, although this original limestone quarried product is our preference. When should I use MOT Type 1 - Limestone. MOT Type 1 - Limestone by its very nature as a Type 1 SHW certified product is a high quality fill or sub-base material and is often used in the construction of car parks ...

How much does a cubic metre of crushed concrete ( type 1 ...

Jul 26, 2007· For crushed concrete, you will need the packing fraction, i.e fraction of concrete. The air spaces will depend upon the shapes of the concrete particles. Assuming an approximate spherical shape, the packing fraction is 74%, so I reckon the density of crushed concrete would be approximately 1.8 tonnes per cubic metre.

DIY Conversion Tables and Conversion Information | DIY Doctor

Conversion information for all manner of materials including, lengths, volume, weight, depth, area, coverage and more. Conversion information for all manner of materials including, lengths, volume, weight, depth, area, coverage and more ... 1.76 tonnes per cubic metre: gravel (MOT Type 1 scalpings) = 1.92 tonnes per cubic metre: shingle = 1.62 ...

Convert volume to weight: Gravel, dry ¼ to 2 inch - AquaCalc

Gravel, dry 1/4 to 2 inch weighs 1.682 gram per cubic centimeter or 1 682 kilogram per cubic meter, i.e. its density is equal to 1 682 kg/m³. In Imperial or US customary measurement system, the Gravel, dry 1/4 to 2 inch density is equal to 105 pound per cubic foot [lb/ft³], or 0.9723 ounce per cubic inch [oz/inch³] .

Weight Conversion Tables - Littler Bulk Haulage

Weight Conversion Tables. How may tonnes in a cubic metre Dry sand fine 1.28 tonnes per cubic metre Dry sand coarse 1.6 tonnes per cubic metre Topsoil (some moisture) 1.44 tonnes per cubic metre Ballast 1.76 tonnes per cubic metre Gravel MOT Type 1 scalpings 1.92 tonnes per cubic metre Shingle 1.62 tonnes per cubic metre

Buy Recycled Aggregate Type 1 Graded | Dorset Delivery or ...

Recycled Type 1. Recycled hardcore crushed at 40mm down to dust, suitable for driveway construction. ... suitable for driveway construction. Recycled Aggregate Type 1 Graded Collection prices: £18.00 Per Tonne Loose £34.38 Per Bulk Bag ... gravel, aggregates, decorative stone, building materials, construction materials and landscaping ...

Density of Construction Materials in kg/m3 and lb/ft3

Density of construction materials are its mass per unit volume of materials. It is expressed in kg/m3 or lb/ft3 and shows compactness of building material. Density is also called as unit weight of substance. It is represented by symbol called row (p). Density represents the degree of compactness of ...

Standard Weights for Crushed Rock Per Meter | Hunker

Solid rock is estimated at 2.5 to 3tons per cubic meter. If rock is crushed into uniform sizes, the presence of open space between the particles causes the load to be lighter -- approximately 1.6 tons per cubic meter. Mixed sizes of crushed rock can range from 1.6 to 2.2 tons per cubic meter.

Unit Weight of Materials Used at Construction Site

Following table shows unit weight of materials used at construction site. Please note this is for reference purpose only and may vary from place and type of material.

Type 1 subbase density - Materials Man - Construction ...

Perhaps on reflection 2.1/2.2 t/M3 should be 2.2/2.3 t/M3. Had another OMC/MDD done and the MDD of 2.4 is now 2.2, so I'm going back to 2.1/2.2 t/M3 compacted density in the layer. Remarkably I've had 244 hits on my site for type 1 subbase density and 691 for type one subbase, and that's not all the search variants such as subbase tonnes M3.